Global 40 Expansion UHD

@Panther I actually skipped that step. It works now.
Thank you so much!

@panther right on . I’m glad it’s working ok for others. The switch from firefox to Brave and the ubuntu update only thing I can think of that changed on my end.

Thanks again for all that you do :grin: :+1:

@Panther thank you Panther. Was already thinking I need to redo move, and have also gotten similar advice from Simon. I very much appreciate this board and the folks here.

I have Pacific 1940 2nd ed. game that I bought in May '13 or thereabouts. Convoy rules are on pp. 22-23. They read like the Europe/L.Harris rules that Gargantua has cited: units roll dice, 2 for a/c and subs, and 1 for others. Rolls of “3” or less are tallied, etc. Exactly like my Europe '40 2nd ed. rulebook in game I purchased the same day.

The Pac. '40 2nd ed. rulebook in A&A.org / Resources section is like the one that came with my game.

I did look at Avalon Hill site for Pac. '40 2nd ed. rulebook and it reads the way that Gargantua is citing for Pacific rules, units do an amount of convoy ipc damage without rolling dice. Looked again at cover of that book, however, and it does not indicate “2nd Edition”. Seems like a bad link at AH site. Rulebook link on Pacific '40 2nd ed. page opens 1st ed. book?

Also confirmed that my Pacific rulebook on pg. 10 says that China is not subject to convoy disruption, as P@nther previously noted.

Right, this is supposed to be the only map-change from 1st editon to 2nd edition.
TripleA 1940 Alpha 3 for example reflects the map of the first edition,
TripleA 1940 Second Edition has the change, but only technically; that means that you cannot enter Yukon in (TA) G40 second edition.

For sure.  Thanks Veqryn

@Veqryn:

Global 1940 2nd Edition, version 3.7 is released

download it now!

changes from 3.6 to 3.7:

1. fixed japanese national objective so that if germany/italy takes india and/or the other power centers in asia, that japan gets her money

2. allowed rockets to gang up on infrastructure

3. Added some things to the game notes about what is NOT covered by the engine (and therefore, what you need to manually keep in mind):

Rules the engine does not do, but you must follow:

Do not allow blitzing or movement through Friendly Neutrals. Air units may not land in or move through Friendly Neutrals, including the same turn they are captured. Friendly Neutrals can not be ‘captured’ with an AA Gun, only by land units with an attack power. Air units may not move through Unfriendly Neutrals unless they are attacking them. Air units may not move through a Neutral territory IF that neutral territory had been attacked on some previous turn by some power (because technically that neutral stops being neutral at that point, and joins the other side). If UK Pacific captures Japan, the money goes to UK Pacific, even if UK Pacific’s capital is occupied. Do not allow USA movement to end in any Sea Zone that touches a Japanese owned territory (Sea Zones 6, 17, 19, 20, 22, 32, 33, 34, 36, and 37). You must place all units you purchased if you are able to, or as many as you can. Any units not placed get refunded to you (triplea instead carries them over to the next turn). The victory conditions must be held for a full continuous round after they are achieved (so for example if Italy takes Egypt as the 8th European VC, then the Axis must hold 8 VCs continuously until Italy’s next turn).

Lastly, I wish to introduce 2 things that everyone may not know already exist within the TripleA engine:

1. Edit Move Units
To “Edit Move”, you must first be in some movement phase.  
Then turn on Edit Mode.
On the right side you see some tabs: “Action” tab, and “Edit” tab, and other tabs.
When you turn on edit mode, you switch automatically to the ‘edit tab’.  However you can still perform ‘actions’ during edit mode, and edit mode changes those actions to reflect that you are in edit mode.
So now click on the “Action” tab, and then move the units just like you would normally.
Because you are in edit mode, the movement validation is turned off, so this allows you to basically move units where-ever you want, including moving enemy units, or even making an enemy attack, or loading transports, etc.

2. Game Comments (aka: a way to tell what fighter is on what carrier, among other things)
Click “View” menu, then select “Show Comment Log”
From there, you can type out and add comments to the game.  The comments will go into the History Panel, and be permanently added to the game save.
Things you could possibly use this for: telling your opponent which fighter is on which carrier, when you have a mixed-nation fleet.

Global 1940 2nd Edition, version 3.8 is released

download it now!

changes from 3.7 to 3.8:

Moved Politics phase to be after Purchase phase and before Combat Move phase. China can declare war on European Axis if they move into China’s allowed movement range. ANZAC can now declare war on True Neutrals. Added the 1942 scenario.