Axis & Allies storage. Post yours!

Hey everyone,
Sharing my global game now that i’ve spent a good amount of effort customizing it.

Custom Map:
I traced @Tjoek 's map in a website program called “inkarnate” and colored it myself. Then in Gimp I added roundels and labels to everything again using Tjoek’s roundels page for the base roundels. The map is just a tad larger than the OOB map as I unforuntly don’t have a huge space for the setup table. I really like the way it turned out visually as I love the more simple look. This was printed at 200dpi (a little low imo) from an online service in the US called Smartpress on .40 Styrene. It cost $150.00 shipped.
IMG_1717.jpeg
IMG_1723.jpeg

Custom Table:
Table is built out of 2x4’s and plywood. Nothing fancy just a big flat surface.

Custom Chart Board/magnetic roundels:
A small magnetic white board with my custom charts printed on vinyl applied to it. The magnetic roundels are my design as well and are 3d printed.
IMG_1719.jpeg -resized.jpeg)

Battle Board:
3d printed base with a vinyl printed sticker on top designed by me. It incorperates the tech units and combined arms into it.

Money Chips:
These are just cheap chips from amazon and I use white for 1 green for 2 red for 5 and blue for 10. Way nicer in the hand than paper money.

Magnetic Units:
Small magnets 3x1mm glued to almost all planes (japan tac bombers needed the larger 3x2 because of the wheels) using ca glue and activator to set them up quickly. A lot of work to get them all done but very rewarding. Carriers got holes drilled and 3x2 magnets inserted as close to the surface of the deck as I could to get the planes to stick nicely to them.
IMG_1710.jpeg

Flight Stands:
These are made from 3mm thum nuts and 3mm acrylic rod. I designed a number of jigs for accurate cutting, gluing and magnet gluing to get them as cleanly done as possible. They have a 3x2mm magnet glued to the top.

Storage:
All of the unit storage boxes are custom designed to hold chips and roundels nicely. My original designs allowed for all of the bins to fit back in the game boxes but for ease of use I eneded up making more boxes/changing the shape so they no longer would go back into the game boxes.
IMG_1714.jpeg
IMG_1716.jpeg

Troop Placards/Placard Markers:
These are a 3d printed base with another label applied to them. I did crop/adjust the flags so they would all be the same dimensions and I took a lot of liberty with the Anzac one (AUS and NZ mashed up). The markers are the same flag just double sided and small enough to fit into territories nicely.
IMG_1713.jpeg

Facilities and Neutral Troops:
All of the facilities are of my design and are all 3d printed with a .2 nozzle. I did keep them small so they didn’t occupy too much board space. The neutral troops are nice as they blend into the space but still represent the troops in a tactile way.
IMG_1721.jpeg

Roundels:
These are just a simple 20mm circle 3d printed with a 19mm laminated sticker attached. These were punched with a “3/4 paper punch”. Very time consuming but the result is hard to argue with.

Thank you for sending the map to my printer. I have been testing scenarios out with my A&A using my 1942 second edition. I just have been using sticky note paper to mark my Italian territories. I used the game pieces from my anniversary addition for the Italian pieces. I also added have tracks: cost is IPC 5. Attack 2, defend 2 as tanks cost 6 IPC in this version. Its nice to spend 5 IPC on an actual unit other than an AA gun. No artillery bonus on half track in this version
I also added the recruitment center from zombies.
Please see the chart below
MOBILIZATION ZONE
UNIT STATS COST MOVE ATTACK DEFENSE
LAND UNITS
INFANTRY 3 1 1 2
ARTILLERY 4 1 2 2
HALF TRACK 5 2 2 2
TANK 6 2 3 3
ANTIAIRCRAFT ARTILLERY 5 1 0 1
RECRUITMENT CENTER 10 0 0 0
INDUSTRIAL COMPLEX 15 0 0 0

AIR UNITS FIGHTER 10 4 3 4 BOMBER 12 6 4 1 SEA UNITS SUBMARINE 6 2 2 1 TRANSPORT 7 2 0 0 DESTROYER 8 2 2 2 CRUISER 12 2 3 3 AIRCRAFT CARRIER 14 2 1 2 BATTLESHIP 20 2 4 4

@scmods said in Axis and allies classic enhanced 2.0:

Your pieces look great.
What kind/brand of paint did you use?
Did you brush paint or use an airbrush?

Thanks! This video should answer everything but in short I used Tamiya’s spray paints except for the Japanese. They got the airbrush.

https://youtu.be/82QytbqxJD8

@Dafyd:

or the little “IG JOES”

:lol: :lol: :lol:

That is very impressive.

YG,

@Young:

Would love to hear from those who have used the file to print their own copy of my custom map… do you have one?
––I would have to say,…NOT YET ! But once I get my latest project going, which will include a large area for a
“GRAND SIZE” War Simulations Room I’ll certainly get in contact with ya’ll.
––I must say, on behalf of all of the other gamers that you’ve already helped with your wonderful map;
THANK YOU !

Tall Paul

Thanks.

The next group of infantry, will be, DESERT LIGHT INFANTYRY.

Until next time.

Cheers!

John

@aaronimpulse:

Should have tried to sneak the maple leaf in there somewhere!

Like most artists, the obvious often evades me. Next version I will definitely do that.

Yrs.,
R.