1.9 map updating problems

@freh said in Mongolia problem:

Sometimes it would trigger at the beginning of the combat phase, before any battles were run, which is strange.

ok so it does fire before combat. It must need a unit presence in Amur then and not just control. Should be able to add a condition for control only.

Just have to make sure it only works when JPN declares war

Thanx for the info

Thanks for getting back to me on this. I’ll post on there. Maybe someone there could also look at implementing a similar change to the other map which also has this optional rule. :-)

Dice stats settle luck debates.

@Veqryn:

Global 1940 2nd Edition, version 3.7 is released

download it now!

changes from 3.6 to 3.7:

1. fixed japanese national objective so that if germany/italy takes india and/or the other power centers in asia, that japan gets her money

2. allowed rockets to gang up on infrastructure

3. Added some things to the game notes about what is NOT covered by the engine (and therefore, what you need to manually keep in mind):

Rules the engine does not do, but you must follow:

Do not allow blitzing or movement through Friendly Neutrals. Air units may not land in or move through Friendly Neutrals, including the same turn they are captured. Friendly Neutrals can not be ‘captured’ with an AA Gun, only by land units with an attack power. Air units may not move through Unfriendly Neutrals unless they are attacking them. Air units may not move through a Neutral territory IF that neutral territory had been attacked on some previous turn by some power (because technically that neutral stops being neutral at that point, and joins the other side). If UK Pacific captures Japan, the money goes to UK Pacific, even if UK Pacific’s capital is occupied. Do not allow USA movement to end in any Sea Zone that touches a Japanese owned territory (Sea Zones 6, 17, 19, 20, 22, 32, 33, 34, 36, and 37). You must place all units you purchased if you are able to, or as many as you can. Any units not placed get refunded to you (triplea instead carries them over to the next turn). The victory conditions must be held for a full continuous round after they are achieved (so for example if Italy takes Egypt as the 8th European VC, then the Axis must hold 8 VCs continuously until Italy’s next turn).

Lastly, I wish to introduce 2 things that everyone may not know already exist within the TripleA engine:

1. Edit Move Units
To “Edit Move”, you must first be in some movement phase.  
Then turn on Edit Mode.
On the right side you see some tabs: “Action” tab, and “Edit” tab, and other tabs.
When you turn on edit mode, you switch automatically to the ‘edit tab’.  However you can still perform ‘actions’ during edit mode, and edit mode changes those actions to reflect that you are in edit mode.
So now click on the “Action” tab, and then move the units just like you would normally.
Because you are in edit mode, the movement validation is turned off, so this allows you to basically move units where-ever you want, including moving enemy units, or even making an enemy attack, or loading transports, etc.

2. Game Comments (aka: a way to tell what fighter is on what carrier, among other things)
Click “View” menu, then select “Show Comment Log”
From there, you can type out and add comments to the game.  The comments will go into the History Panel, and be permanently added to the game save.
Things you could possibly use this for: telling your opponent which fighter is on which carrier, when you have a mixed-nation fleet.

Global 1940 2nd Edition, version 3.8 is released

download it now!

changes from 3.7 to 3.8:

@Veqryn:

a very very very minor bug

Yes, indeed!

TripleA has definitely improved a lot. Thanks to you and the other developers!
:-)

did you download the source code or did you download the installed?
go download the installer,
double click it, it will install the game

Thanks.

It is Clauswitz’ post of April 26, 10:54 PM.

Right click, “save target as”, and then rename the file as “Temporal.properties”.  Next time you start up Triple A, viola!