Cyanight's Customizations

Hey everyone,
Sharing my global game now that i’ve spent a good amount of effort customizing it.

Custom Map:
I traced @Tjoek 's map in a website program called “inkarnate” and colored it myself. Then in Gimp I added roundels and labels to everything again using Tjoek’s roundels page for the base roundels. The map is just a tad larger than the OOB map as I unforuntly don’t have a huge space for the setup table. I really like the way it turned out visually as I love the more simple look. This was printed at 200dpi (a little low imo) from an online service in the US called Smartpress on .40 Styrene. It cost $150.00 shipped.
IMG_1717.jpeg
IMG_1723.jpeg

Custom Table:
Table is built out of 2x4’s and plywood. Nothing fancy just a big flat surface.

Custom Chart Board/magnetic roundels:
A small magnetic white board with my custom charts printed on vinyl applied to it. The magnetic roundels are my design as well and are 3d printed.
IMG_1719.jpeg -resized.jpeg)

Battle Board:
3d printed base with a vinyl printed sticker on top designed by me. It incorperates the tech units and combined arms into it.

Money Chips:
These are just cheap chips from amazon and I use white for 1 green for 2 red for 5 and blue for 10. Way nicer in the hand than paper money.

Magnetic Units:
Small magnets 3x1mm glued to almost all planes (japan tac bombers needed the larger 3x2 because of the wheels) using ca glue and activator to set them up quickly. A lot of work to get them all done but very rewarding. Carriers got holes drilled and 3x2 magnets inserted as close to the surface of the deck as I could to get the planes to stick nicely to them.
IMG_1710.jpeg

Flight Stands:
These are made from 3mm thum nuts and 3mm acrylic rod. I designed a number of jigs for accurate cutting, gluing and magnet gluing to get them as cleanly done as possible. They have a 3x2mm magnet glued to the top.

Storage:
All of the unit storage boxes are custom designed to hold chips and roundels nicely. My original designs allowed for all of the bins to fit back in the game boxes but for ease of use I eneded up making more boxes/changing the shape so they no longer would go back into the game boxes.
IMG_1714.jpeg
IMG_1716.jpeg

Troop Placards/Placard Markers:
These are a 3d printed base with another label applied to them. I did crop/adjust the flags so they would all be the same dimensions and I took a lot of liberty with the Anzac one (AUS and NZ mashed up). The markers are the same flag just double sided and small enough to fit into territories nicely.
IMG_1713.jpeg

Facilities and Neutral Troops:
All of the facilities are of my design and are all 3d printed with a .2 nozzle. I did keep them small so they didn’t occupy too much board space. The neutral troops are nice as they blend into the space but still represent the troops in a tactile way.
IMG_1721.jpeg

Roundels:
These are just a simple 20mm circle 3d printed with a 19mm laminated sticker attached. These were punched with a “3/4 paper punch”. Very time consuming but the result is hard to argue with.

Part 4: Starting the ships, adding decals to the tanks, skin tones on the soldiers

Today spent some time adding paint to the sprayed ships, including painting the water jettisons on the subs black (this was very tricky and ended up looking a little sloppy). Advice for painting the jettisons: toothpicks are not small enough! If you do use toothpicks, you’ll have to dab a dot of black for each tiny jettison.

The battleships were a bit easier, and painting the decks, bridge, and smoke stacks were all done in silver. I plan on adding the final grey coat last after the deck and stacks/bridge dry. I experimented with how to add the national emblem, and will probably opt for a white background with a red dot on the bow of the ship. In the future I may do that with the rear end of the ship.

I painted the tranny smoke stacks silver and added a white background for the emblem on the destroyers. All in all, the Japanese navy is coming along nicely.

The armor is pretty much done. I added a white flag to the front side of the armor and will be adding the red dots later. For the aircraft, I’ll be adding a red band around the rear part of the plane. I was debating between sky blue and red and may alternate just for some variety.

The soldiers got some skin! And I just want to say that adding the paint alone brings out the contours of their facial features in an excellent manner on their own. I may add a touch of black to certain areas of the face but that will be a last step. The next step will be panting their uniforms, rifles, and helmets.

After all this is done, I will be spray painting the japanese bombers white, the aircraft carrier black, and then will add the details to those. The Japanese are about 55% done all in all and I’m pleased with the results so far even if they do look a bit amateurish. Stay tuned.

IMG_6405.JPG IMG_6404.JPG IMG_6403.JPG IMG_6402.JPG

Appreciate the comments. You must have been busy the last few days. Haven’t seen any of your work.

Are you and your friend painting anything, this week?

Just had your G40 deck from ArtsCow delivered to Wales. They look great and will be very useful for our group as we’ve only played G40 once before and AA50 a handful of times. Thanks for making them available 😊

I did have one question, what are the numbered naval cards for? I’m assuming it’s either something to do with damage to capital ships or for easier tracking of big fleets but I could be wrong on both counts!

Cheers

Very nice indeed.

@dangermouse650:

@John:

@dangermouse650:

Great work John

Thanks DM.

Where have you been?

Have you been working, as of late?

Yes, work has been very hectic and other life happenings that are keeping me too busy to paint……but keep up with yours your doing great. :-)

Appreciate it DM. I hope you get to paint soon. :-)

John

Thanks Spitfire38, for your kind words and encouragement, as well. Yes, looking forward to meeting you someday as well, whether painting or playing.

Thanks buddy! :-D

Cheers!

John

Sounds great!