Toblerone77's Paint Warfare.

Here’s another pic in dimmer light, which is a better comparison to the before picture above.

The silver pops nicely. Before, in the same lighting situation, I couldn’t see most of the border lines at all.

I used the Edding 5300 silver acrylic paint marker with a 1-2 mm tip
The silver seems to really catch what little light there is in the room.

As the paint the marker ran low of paint it was harder and harder to control, so I reccomend just stopping and using a fresh paint marker if this happens. A few of the last lines I did are fatter than I would like because of this.
But the overal result is a huge improvement.

IMG_20230304_154631.jpg

@cavestone I also use vallejo paints. The key question here is are you brush painting, or using an airbrush, or both?

The Vallejo paints have a “Model Air” line that comes pre-thinned. You can buy a thinning product (from them) to add to the “Model Color” series paints, which are the exact same thing, just more concentrated and thicker.

If you’ve never used an airbrush, its a bit finicky–it requires regular cleaning and a without a good brush and compressor the paint will flow very inconsistently. The process will be very frustrating unless you use the pre-thinned paints because the brush can only blow paint that is within a certain set of thickness parameters that are difficult to achieve, especially if you are trying to mix the air in the brush’s reserve or in small quantities. That’s why having copies of both Model Air and Model Color is fine by me–unlike Warhammer 40K I’m using primarily earthy colors, greens, dunkelgelb and dunkelgrau… other AFV and camoflage colors and so i don’t need a collection of primary or bright colors.

But I recommend it. The airbrush creates a sublime, beautiful layer and slight mix variations can be used to create shadows, grades, etc. Then you go back over with your brush, adding highlights, lines, details. Then, back over again with a drybrushing…then back to the airbrush to blast Flory Wash all over it.

Can’t see your photos, you can’t post photos until you have a certain post count. I wouldn’t use water to thin paints, they are water soluble but the mix and viscosity is all wrong (though water is obv. cheap and easy to clean up)

As for oil-based paints, these require thinner to clean up, they are much more difficult to drybrush with and are not used for airbrushing. The days of the old testors paints is long behind us–even apple barrel paints are easier to work with and cheaper. The early painting methods were much more about glomming thick layers of paint onto lead miniatures and the modern approach with water based paint and a series of different techniques creates much better results.

@siredblood

Hello,

I wanted to print some of the really cool Axis and Allies money but cannot find the files that people are referring to. I tried the link but there was no file. Can anyone help ?

Thank You.

Thanks Spitfire38, for your kind words and encouragement, as well. Yes, looking forward to meeting you someday as well, whether painting or playing.

Thanks buddy! :-D

Cheers!

John

Regarding prices, here are some quotes that I got from two different Southern California print shops  (I had posted this also on the thread entitled Ambilzi & Grasshopper’s 1940 Global Map)

The first print shop provided the following estimates (note the $52 set up fee):

SET UP:  $52.05 ( digital color file set up, latex printer set up)

48" x 105" vinyl $142.63  print digital color 4/0 on white smooth vinyl (15oz)

48" x 105" canvas  $300.13  print digital color 4/0 on canvas

48" x 105" versa fabric  $273.88  print digital color 4/0 on versa fabric

53" x 116" vinyl  $174.63 print digital color 4/0 on white smooth vinyl (15oz)

53" x 116" canvas $368.13  print digital color 4/0 on canvas

53" x 116" versa fabric $335.88 please note: print cannot be any larger, printing on a 54" rolld

A second set of quotes from a different Southern California printing company for printing on vinyl (the type of material used for advertising banners):

48"x105" ,  white 64" Roland EcoSol Banner, solvent 6 color Roland 4sf  $230.80

53"x116",    white 64" Roland EcoSol Banner, solvent 6 color Roland 4sf  $258.78

56"x122.5",  white 64" Roland EcoSol Banner, solvent 6 color Roland 4sf  $277.42

(I might check on the AliBaba website to see what I can find for printing services in China.  Also, I’m checking on the possibility of printing on upholstery vinyl and marine vinyl).

**Great work! Those are awesome. **

Is there something wrong with the pictures on the first couple of pages of this thread?  I only see a placeholder, generic image icon where the pictures should be.  :?

Fellow A&A Gamers,

––This thread will eventually contain ALL of the Anzac units that I’ve had detailed & painted by the “WARMACHINE Team”.

––So far the list includes:

ANZAC

ANZAC ARMY
Anzac Infantry
––Anzac (Infantry, Rifle)…(Starting at message #1)
Anzac Armored Vehicles
––M-3 Stuart “Honey” (Tank, Light)…Outback Camo scheme…(Starting at message # )

–-----------------------------------------------------------------------------

Everyone.

----Here are the Anzac Rifle Infantry that Chad Coffman, a.k.a. “Allworkandnoclay”, painted for me. All 20 of the Australian Infantry, nick-named “Diggers”, after their WWI fight at Galipoli, are shown here in a group portrait just after completion by Chad. Note the intricate Anzac ensign he painted on their bases. This guys painting talent is simply awesome! So just sit back, put another shrimp on the barbie, and enjoy, mate.

“Tall Paul”
anzac_inf2b.jpg

@elrojo33:

That would be my answer. Anyway, I’ll keep an eye out. If I come across some I will let you know.
Happy hunting.

Thanks much.