Dangermouse finally found some time to paint…..

@cavestone I also use vallejo paints. The key question here is are you brush painting, or using an airbrush, or both?

The Vallejo paints have a “Model Air” line that comes pre-thinned. You can buy a thinning product (from them) to add to the “Model Color” series paints, which are the exact same thing, just more concentrated and thicker.

If you’ve never used an airbrush, its a bit finicky–it requires regular cleaning and a without a good brush and compressor the paint will flow very inconsistently. The process will be very frustrating unless you use the pre-thinned paints because the brush can only blow paint that is within a certain set of thickness parameters that are difficult to achieve, especially if you are trying to mix the air in the brush’s reserve or in small quantities. That’s why having copies of both Model Air and Model Color is fine by me–unlike Warhammer 40K I’m using primarily earthy colors, greens, dunkelgelb and dunkelgrau… other AFV and camoflage colors and so i don’t need a collection of primary or bright colors.

But I recommend it. The airbrush creates a sublime, beautiful layer and slight mix variations can be used to create shadows, grades, etc. Then you go back over with your brush, adding highlights, lines, details. Then, back over again with a drybrushing…then back to the airbrush to blast Flory Wash all over it.

Can’t see your photos, you can’t post photos until you have a certain post count. I wouldn’t use water to thin paints, they are water soluble but the mix and viscosity is all wrong (though water is obv. cheap and easy to clean up)

As for oil-based paints, these require thinner to clean up, they are much more difficult to drybrush with and are not used for airbrushing. The days of the old testors paints is long behind us–even apple barrel paints are easier to work with and cheaper. The early painting methods were much more about glomming thick layers of paint onto lead miniatures and the modern approach with water based paint and a series of different techniques creates much better results.

Part 4: Starting the ships, adding decals to the tanks, skin tones on the soldiers

Today spent some time adding paint to the sprayed ships, including painting the water jettisons on the subs black (this was very tricky and ended up looking a little sloppy). Advice for painting the jettisons: toothpicks are not small enough! If you do use toothpicks, you’ll have to dab a dot of black for each tiny jettison.

The battleships were a bit easier, and painting the decks, bridge, and smoke stacks were all done in silver. I plan on adding the final grey coat last after the deck and stacks/bridge dry. I experimented with how to add the national emblem, and will probably opt for a white background with a red dot on the bow of the ship. In the future I may do that with the rear end of the ship.

I painted the tranny smoke stacks silver and added a white background for the emblem on the destroyers. All in all, the Japanese navy is coming along nicely.

The armor is pretty much done. I added a white flag to the front side of the armor and will be adding the red dots later. For the aircraft, I’ll be adding a red band around the rear part of the plane. I was debating between sky blue and red and may alternate just for some variety.

The soldiers got some skin! And I just want to say that adding the paint alone brings out the contours of their facial features in an excellent manner on their own. I may add a touch of black to certain areas of the face but that will be a last step. The next step will be panting their uniforms, rifles, and helmets.

After all this is done, I will be spray painting the japanese bombers white, the aircraft carrier black, and then will add the details to those. The Japanese are about 55% done all in all and I’m pleased with the results so far even if they do look a bit amateurish. Stay tuned.

IMG_6405.JPG IMG_6404.JPG IMG_6403.JPG IMG_6402.JPG

Thank you both so much, I feel a lot better about painting now.  :-D

@jwo1984:

hey guys, so I was searching some camo desert schemes for HBG’s Valentine medium tank and came across this one. � However looking at the sculps I knew it would be tough to paint these blue lines in because most of the tank is all track! so I cut out and shaped some track guard armour like the photo below just using some clear flexible plastic and glued in too the sides…making these two tanks mk II’s which look to have had the side armour as a pose to the Mk V that HBG has sculpted.

I’m sure whatever you do too it, it will turn out great. Can’t wait too see it painted. Good luck buddy! :-D

Following up:

I went out and bought a can of chrome spray-paint from a Blick arts-and-crafts store, and did a few tests on some B-17’s…

I’ll post pictures if anyone wants to see them.  It looks great.  Nice, even coating… very lustrous.  With some added details I think my late-war aircraft are going to look amazing.

Thanks for the feedback, everyone.

Wow!  Such cool pieces! (Been awhile Paul)  And there’s others I’ve yet to see that are posted -

Fantastic!  Especially love seeing the whole army together - the Ruskie horde!

@BluGerman:

today i managed to read through this year long forum thread and I have to ask what happened after November 17th 2011?.. did everybody in this forum mysteriously dissapear? or was it just discontinued? or was it moved to another forum thread or something?.. somebody please let me know because I was really excited to see Allworks whole board with his miniatures (they are awesome!)

In answer to your question- I don’t really know.  :? Allworkandnoclay is an artist who does all sorts of other work for money, not just Axis and Allies. I presume that he moved on to other work, as his Flickr account shows him doing some sculpting and what not. To be honest though, he stopped posting pics, people stopped commenting, and it sort of fell of the face of the earth. There’s some stuff on TallPaul’s page, and there are plenty of other artists with some awesome stuff if you need your daily fix of painted minis!