1940 Global table & painted pieces

I have been playing around with different configurations for a custom table and wanted to note some things I’ve landed on that I really like. A main one thing is having the map mounted so that it can slide around as needed on top of a bigger playing area. My table is 65” x 95” in total with a 5.5” arm rest around the outside and the middle is a recessed neoprene surface. I have the OOB Global map mounted on 1/2” rigid foam with a 1/2” aluminum frame around it. This allows the map to slide up close to whoever’s turn it is, but then be in the middle so both players can roll dice In front of them without disturbing the map and in easy view of the other player. (Plus we like lots of room to roll the bones). This ability to adjust the surface along with a standing height, makes it comfortable for long uses because you can move around more and don’t feel as tied down.
Things I’ve learned and changed from original design - I originally used too big of a frame for the map and mounted it on too high of a foam block (you can see these pictures at the bottom) - it made it hard to see the other player’s dice and the big frame took up too much real estate. My global map is mounted on much thinner foam (the framing is bad, you can see if you look closely) but I also used much thinner aluminum angle for the frame. This gives just enough grip when needing to move the map around (I use furniture slides on the bottom, which glide very nicely on the neoprene) but doesn’t make the whole thing too bulky. Having it an inch or so off the surface keeps the dice off, but isn’t so heigh that you can’t see the other player’s dice rolls. When playing other versions (such as Zombies) the board is much smaller, but it can easily swap in and out on the same table since it can move around where ever it is needed or be pushed aside.
I originally made it normal table height, but found long reaches while sitting were harder and it just felt cramped. Standing height with a bar stool is a great way to have the best of both worlds.
The 5.5” rim around the table itself gives you a nice arm rest that doesn’t interfere with the gaming surface. I’m playing with how to best add some cushion to this part - open to suggestions. Sometimes I just lay a piece of leftover neoprene on it.
Dice bounce nice on the neoprene and stay off the floor. It also feels nice and has enough give to allow things to slide but be picked up easily. Wouldn’t definitely go with neoprene again as a surface covering.
I made the drawers open to the inside of the table so you can stay hunched over the action while accessing and stowing stuff away. 50/50 on whether I would keep this if I were to do it again. If I were doing it again, I might try to build customer drawers form scratch using actual drawer glides, but that was beyond my ability when I first did this, so I just used clear plexiglass boxes with aluminum pulls mounted on them. It’s nice having them clear, and I was happy with how the pulls came out, but without glides they can be a little fussy sliding in and out of their slots.
I originally designed the table so that I could put a cover surface back on top when not in use, but find I don’t really ever do that, so if I were to do it again, I might not mess with that part (I never even finished staining those as you can see in the pictures).
CF362D52-269F-4480-8CBB-08139099138F.jpeg A9E12EA1-66EB-4671-86AC-68C62FD30AD5.jpeg 858DE1F2-030A-4D5A-93E4-70A7D1180ADB.jpeg 8F513EE0-DA37-4BA9-880E-4D5EF7BF431F.jpeg F0188165-757B-4CC1-BF67-5045832283C9.jpeg 2E3CD627-0D31-4121-ACF8-682F9F58A40B.jpeg

Ah, yet another good use for the coasters!

I was awarded the Customizer badge at some point unknown, but marked on my pictures post as to when I found out I was a recipient. There is a post somewhere on the forums that tells of the process and from what I recall one has to be nominated by someone to a moderator and there is some sort of review process. Here’s a link to the award discussion thread: https://www.axisandallies.org/forums/topic/24173/customizers-round-2

Glad you enjoy the pics and tips! We all inspire each other with our pictures, tips, and techniques, so keep sharing!

@655321 decals very small decals and I bought 3 of those sets so there is that. Lol

4E43E286-8F3E-4AC1-84BC-E732B0B7EB2F.jpeg CA95B30E-914A-4105-9C05-22B533ECF2FF.jpeg

Thank you for the positive feedback! I forgot to say that in the previous post, and it’s very important that I do. It’s very encouraging and motivating to get good feedback, and we certainly appreciate it. The above mentioned four Essex class carriers are complete, a long with several other ships of the US Navy, so its time to update the thread. Just ships by FOlewnik in this post. More aircraft are almost done but I haven’t put magnets in them yet (so not really done), so no aircraft pictures this post.

We’ll start with the two “odd men out” of the HBG sculpt Baltimore Class Heavy Cruisers. Why “odd men out”? Because in the below picture we have on the left, the USS Unnamed Baltimore Class Cruiser Wearing Measure 31a, Design 9C, and on the right is the USS Columbus (CA 74), which wasn’t commissioned until June 8, 1945. The cruiser with the long name is wearing a design that was never used, but was taken from a period design found at https://www.wikiwand.com/en/World_War_II_US_Navy_dazzle_camouflage_measures_31,_32_and_33:_cruisers. The USS Columbus is wearing a Measure 12 Modified designed by FOlewnik to match the pieces we’ll be using for the US Atlantic fleet. These will get aircraft added, but at the time of the photographs the decals on the wings of the aircraft were drying.
DSC_0510a.jpg
DSC_0511a.jpg
DSC_0512a.jpg
Pattern_sheet,_MS-31a_9C_for_Baltimore_class.jpg

Next up are some metal destroyers from GHQ. Below on the left, the very brave USS Johnston (DD-557) painted in MS-3_/6D as it looked when it was “Sunk by Japanese Warships off Samar October 25 1944,” and next to it is USS Van Valkenburgh (DD-656) painted in camouflage Measure 31, Design 9d. All Wartime photos taken from Navsource.org, a great resource for US Navy history buffs.
DSC_0514a.jpg
DSC_0515a.jpg
DSC_0516a.jpg

Below, the real USS Johnston shortly before her final battle, and the official design sheet:
DSC_0516a0555715.jpg
Pattern_sheet,_MS-31-32-33_6D_for_Fletcher_class.jpg

A great wartime picture of the USS Van Valkenburgh, which is the same on both sides:
DSC_0516a0565603.jpg

Now on to these two. From GHQ, USS The Sullivans (DD-537) painted in Measure 1, and the HBG sculpt light cruiser USS Marblehead (CL-12) who always wore Measure 2 throughout the war. If I can get FOlewnik to put the Shamrock on the first stack of The Sullivans when he puts the scout aircraft on the Marblehead, as seen in the below wartime photograph, I’ll come back and edit the post.
DSC_0520a.jpg
DSC_0522a.jpg
DSC_0519a.jpg
DSC_0520a0553740.jpg
DSC_0520a0401208.jpg

The post previous to this post showed four Essex Class sculpts from HBG getting prepped and started with a base coat. Those are now completed and I had too much fun playing with them and the aircraft (that are complete so far) while I was taking photographs. I’m pretty sure I didn’t make any wooshing sea or aircraft noises or FOlewnik would have laughed at me. I was tempted though, and here’s why:
DSC_0524a.jpg
DSC_0525a.jpg
DSC_0526a.jpg
Above we have the first of the Long Hull Essex Class, USS Ticonderoga (CV-14) on the left looking as she did after her April 1945 refit from suffering a Kamikaze Attack on January 21, 1945, and USS Bunker Hill (CV-17) on the right. The Bunker Hill is wearing Measure 33, Design 6A, of which Navsource says, “Her port side camouflage pattern was the most intricate design applied to any carrier.” One glance can confirm that!
DSC_0526a021772.jpg

The final two Essex Class carriers are the USS Essex (CV-9) herself, and the USS Bennington (CV-20). The Essex is wearing a unique pattern, Measure 32v6, Design 10D, adapted from a destroyer pattern specifically for the long hulled Essex. The Bennington is painted in Measure 32, Design 17A.
DSC_0527a.jpg
DSC_0528a.jpg
DSC_0529a.jpg
DSC_0529aPattern_sheet,_MS_32a_17A_for_Essex_class.jpg
DSC_0529aUSS_Essex_(CV-9)_in_MS_32_6-10D_camouflage.jpg

Finally, some group pictures just for fun:
DSC_0531a.jpg
DSC_0532a.jpg
DSC_0533a.jpg
DSC_0534a.jpg
Thank you for checking out the post! If you liked it, please click the little heart. I’m trying to figure out why our post is only rated with a 2 when it seems it should be a bit higher if the other likes are any indication.

@aaronimpulse:

Should have tried to sneak the maple leaf in there somewhere!

Like most artists, the obvious often evades me. Next version I will definitely do that.

Yrs.,
R.

“YG”,

@Young:

AWESOME!

––I totally agree with your opinion of “Allworkandnoclay’s” painting talent.
----I’m sure you’d enjoy “SgtWilTan’s” thread about detailing units as well as “LHoffman’s” thread about painting them. They’re both really talented guys!
––In order for you to see all of the new units when they’re completed you might also want to stay tuned to my main thread because Sgt. Wil Tan has already detailed many new units that Lucas Hoffman will have painted before much longer. And I’m glad you enjoyed the “hoard”.

“Tall Paul”

Fellow A&A Gamers,

––This thread will eventually contain ALL of the Anzac units that I’ve had detailed & painted by the “WARMACHINE Team”.

––So far the list includes:

ANZAC

ANZAC ARMY
Anzac Infantry
––Anzac (Infantry, Rifle)…(Starting at message #1)
Anzac Armored Vehicles
––M-3 Stuart “Honey” (Tank, Light)…Outback Camo scheme…(Starting at message # )

–-----------------------------------------------------------------------------

Everyone.

----Here are the Anzac Rifle Infantry that Chad Coffman, a.k.a. “Allworkandnoclay”, painted for me. All 20 of the Australian Infantry, nick-named “Diggers”, after their WWI fight at Galipoli, are shown here in a group portrait just after completion by Chad. Note the intricate Anzac ensign he painted on their bases. This guys painting talent is simply awesome! So just sit back, put another shrimp on the barbie, and enjoy, mate.

“Tall Paul”
anzac_inf2b.jpg

––Calling “Viracocha”----

––My friend,…it’s been way too long since I’ve heard from you. I ALWAYS enjoy my conversations with you.

Tall Paul