Wanted - Axis & Allies Anniversary Edition Italian Tanks

@always-wanderer

That one looks great too! Thank you again for sharing these great resources!

@Vidocq62:

Thank you for the answer.

Do you have to set a high limit on auctions ?

For a first couple games, I’d play with no bid at all. Have one (side/team/person) first play one side and then swap sides. That will help the players involved learn just how much bid they want to have in the future. Bids are more for when competitive players who know how to play the game sit down to rumble. If you just want to play a game one off, just have the experienced players play the Allies and the inexperienced play the Axis.

My 2 IPCs, anyways.

-Midnight_Reaper

Agreed, need and want are different. From what I gather, they only waited about 3 years between 1942.1 and 1942.2.

It’s nice to not have to house rule too much - even using a bid implies some additional play testing would have been beneficial. But to be able to discuss strategies here, etc, requires us to have the same rules. :)

@warTorn:

@vodot:

Guys, use 7zip!

Seriously, freaking WinRAR!? For what- archiving the album of .mp3s you downloaded from napster over the course of an entire evening with your state-of-the-art, 38880 baud, dial-up modem?

I kid, but seriously: www.7zip.org.

EDIT: If you’re on a mac, use this instead (it’s a 7zip port) www.kekaosx.com/

YOU ARE A SAVIOR!!!

:-)

Or you can just download the rulebook from the WOTC site, grab extra units (from other or older games), paint them to match, print a map out created by Imperious Leader and you should be on your way.

This is what I did any way.  Although I went as far as to recreate the Combat board, IPC chart and National Objective/Setup Charts.

I use the roundel with the 3 axes and bushels instead.  It stands out pretty well from the others, and looks better in my opinion (As well as representing the regime intended).  The coloured roundel with the single axe and bushel is nice too.

And I did notice the mistake on the colours of the one they used as well.  I believe Kreighund also had mentioned this?

In addition, I hate the colour they used for the Italian units.  I prefer to use the British units from revised with the light green to represent the Italians instead, as they stand out better.  I may actually take the AA50 Italians and spray them that same light green, but I’m not sure how paint will stick to that shiny plastic.  May need to use an etching primer first.

Or maybe I’ll wait to see if they use a different colour in AAE40.  Wizards seem to like switching colours from game to game.

Check this site out for roundels:

http://commons.wikimedia.org/wiki/Roundel

Cheers

@shifty:

What kind of “program” are you writing?  What equation/algorithm are you using?

It’s written in BlitzMax. The source below should (hopefully :)) not be too hard to understand - if you have questions, feel free to ask:

' Compares 2nd ed. A&A tech dev cost/rate with Anniv. ed. A&A ' 20 turns to test; record turn number that a total of 2 breakthroughs were achieved.  Test 1 & 2 rolls/turn. ' If two breakthroughs aren't achieved, "turn 0" is recorded (ignored for graphing & turn average) ' (When going for two breakthroughs, two aren't achieved in about 2% for both 2nd and Anniv.) Strict Local breakthroughs, totalCost, turn, totalTurns Local answer[21], prefix$, graph$ Local breakthroughLimit = 2 For Local rolls = 1 To 2 ' actual rolls for 2nd Ed, Researchers for Anniv. Print;Print; Print rolls + " Tech Roll(s)/Researcher(s) per Turn:" Print; Print "2nd Edition" totalCost = 0 totalTurns = 0 For Local c = 0 To 20 answer[c] = 0 Next For Local test = 1 To 100000 ' a hundred thousand tests for accuracy breakthroughs = 0 turn = 0 While breakthroughs < breakthroughLimit And turn <= 20 turn :+ 1 totalCost :+ rolls * 5 ' each roll costs 5 IPCs For Local c = 1 To rolls If Rand(6) = 6 Then breakthroughs :+ 1 Next Wend totalTurns :+ turn If turn > 20 Then answer[0] :+ 1 Else answer[turn] :+ 1 EndIf Next ' display results For Local c = 1 To 20 graph = "" ' divide results by 1000 so each asterisk represents one percent For Local cc = 1 To Int(answer[c]/1000.0 + .5) graph :+"*" Next If c < 10 Then prefix = " " Else prefix ="" ' extra space for single digits Print prefix + c + " " + graph Next Print "Avg turn = " + totalTurns / 100000.0 Print "Avg cost = " + totalCost / 100000.0 Print; Print "Anniversary Edition" totalCost = 0 totalTurns = 0 For Local c = 0 To 20 answer[c] = 0 Next Local researchers ' researchers accumulate from turn to turn For Local test = 1 To 100000 researchers = 0 breakthroughs = 0 turn = 0 While breakthroughs < breakthroughLimit And turn <= 20 turn :+ 1 totalCost :+ rolls * 5 ' each researcher costs 5 IPCs researchers :+ 1 * rolls ' accumulate 1 researcher per "roll" Local success For Local c = 1 To researchers If Rand(6) = 6 Then success = True ' only one regardless of # of sixes rolled Next If success Then researchers = 0 ' eliminate accumulated researchers when successful breakthroughs :+ 1 EndIf Wend totalTurns :+ turn If turn > 20 Then answer[0] :+ 1 Else answer[turn] :+ 1 EndIf Next ' display results For Local c = 1 To 20 graph = "" ' divide results by 1000 so each asterisk represents one percent For Local cc = 1 To Int(answer[c]/1000.0 + .5) graph :+"*" Next If c < 10 Then prefix = " " Else prefix ="" ' extra space for single digits Print prefix + c + " " + graph Next Print "Avg turn = " + totalTurns / 100000.0 Print "Avg cost = " + totalCost / 100000.0 Next

I release it into the public domain (modify it as desired/convert it to the language of your choice).  breakthroughLimit is initially set for 2, which generated the first set of graphs in this thread (I hand-rounded the accuracy to a single decimal place when copy/pasting results in the thread). Setting it to 1 (i.e. stopping after getting one breakthrough) produced the second set above. I also made another, slightly tweaked version to generate the “only buy Researchers on turn 1” version for wodan46.